English
Español CO
-
-
-
-
- Products
-
-
- Products
-
-
-
- Brands
-
-
-
-
- Products
-
-
- Doctors and Hospitals
- Products
-
-
-
-
-
- Aluminized Products
-
-
-
- Confined Spaces
- Products
-
-
10 other products:
Demon Gray Af Ansi Z87 + Lens
Glasses for visual protection in polycarbonate, used as primary protection of
according to OSHA recommendations. Suitable for outdoor and indoor work,
designed to protect against high...
Bravo Boot In Steelpro Dielectric Leather Astm F2413- Rh Astm D471 Sole Size 45
Half-round safety boot. Rough Polished Leather Upper
Complies with ASTM 2413-05 - EN 345.
Max load. Crushing load 1500 kg / f - 2270kg (15 KN).
Safety toe cap according to EN...
Sequoia Srt Petzl
Straps for the SEQUOIA SRT pruning seat harness designed to distribute the load between the belt and the shoulders and improve comfort. These straps are connected to the ventral attachment point of the harness and to the two loops located at...
Product Comments
image Featured Descripción
- DESCRIPTION: PANTANERA BOOT
- GENERAL: COUNTER FOR ENHANCED PROTECTION AND EASE TO HEEL BOOT mismatching TOP OF REED WITH GROOVE SYSTEM ON BOTH SIDES FOR EASE OF GRIP
- COLOR: OF THE ASSEMBLY OF THE CANE AND THE CAPELLATION IS BLACK / THE COLOR OF THE SOLE OF THE BOOT IS BEIGE.
- HEIGHT: CORRESPONDS TO THE TYPE OF HIGH ROD BOOT WITH AVERAGE RANGE OF 359 mm.
- HEEL AND SOLE: HEEL WITH HEIGHT OF 26 mm +/- 2mm. OUTSOLE WITH A RELIEF DESIGN THAT OFFERS ANTI-SLIP EFFECT.
- CAPELLADA: REINFORCED WITH RELIEF, LIKE THE COUNTERFURT ROD: WITH TAPE IN TOP PARTS OF 2.8 mm, TO AVOID TEARING; REINFORCEMENT IN REAR OF 22.9 mm.
- DESIGN AND MATERIALS: ERGONOMIC DIRECT INJECTION PVC (polyvinyl chloride), HIGH
- RESISTANCE AND GREAT FLEXIBILITY; 100% WATERPROOF; NON-PLEATED NYLON INNER STOCKING
TECHNICAL DATA: - HEEL AND OUTSOLE WITH RESISTANCE TO 118 mm3 ABRASION - RESISTANCE TO
BENDING AT 150,000 CYCLES OF 9.93 mm
-HARDNESS (SHORE A-15 sec): a) IN THE UPPER OF 62.8 b) IN THE OUTSOLE OF 63.5
- DENSITY IN g / cm3: a) IN THE UPPER OF 1.18 b) IN THE SOLE OF 1.12
- RESISTANCE TO THE EXTRACTION OF OILS BY SOLVENTS (UPPER AND SOLE):
A) MASS LOSS IN GASOLINE (%): a) 0.07 CANE b) 0.01 SOLE
B) LOSS OF MASS IN VEGETABLE OIL (%): a) CANE OF 0.0 b) SOLE OF 0.0
C) LOSS OF MASS IN MINERAL OIL (%): a) CANE OF 0.0 b) SOLE OF 0.0
D) LOSS OF MASS IN WATER-SOAP (%): a) CANE OF 0.0 b) SOLE OF 0.0
- AIR LEAKS: NO EVIDENCE OF AIR LEAKS
- THERMAL STABILITY: NO DEFORMATION OR APPARENT DAMAGE
- TENSION PROPERTIES FOR THE ROD:
a) ELONGATION 4.76 Mpa (Standard requirement: Min 1.5)
b) ELONGATION TO BREAKAGE (%) of 420.72 (Requirement of the standard: Min 170)
- SOLE AND UPPER ADHESION N / cm of 61.03 (Requirement of the standard No less than 30)
